Vedr. Kabler.

check om dine HD/CD kabler sider fast og er iorden.

Det har vi gjort. Det er ikke det...
Ellers andre ideer?? Jeg giver 150 point hvis du kommer med en løsning som får lortet igang....

Desværre ikke :(

spørg måske microsoft om hvad den fejl plejer at komme af ?

Det kan jeg ikke bruge til noget nu..
Kan kablerne være for gamle..

hvis det er brugte kabler kan du have rykket en af lederne løs i stikket de kan være ret skrøbelige hvis de har været pillet af og på flere gange

Hvis du kan læse tysk, så http://www.spacewalker.com/german/realtek.htm

lol det er noget med at boot'e via LAN

Her er en på¨engelsk
If no OS is loaded, this message will appear instead:
PXE-E61: Media test failure, check cable
http://www.hds.com/pdf/8240ref.pdf
Det tyder på at det er et softwareproblem, og ikke noget med kablerne.

Hvorfor er spørgsmålet egentlig oprettet 2 gange?

http://www.eksperten.dk/spm/338814

smækker den ind her også

http://forums.devshed.com/archive/33/2002/07/2/38333

Fejlmeddelelsen 'pxe-e61 media failure' kommer, når maskinen tror den skal boote fra netværk.
http://www.hardwareanalysis.com/content/topic/3822/
Så disky kan godt trække sit lol tilbage.

Q. I have P III HCL busybee, 750 MHz, 192 MB RAM PC. Since last few days, my PC hard disk is making a lot of noise. After booting it shows the following error: For Realtek RTL8139(X) PCI fast Ethernet controller V2.00(991019) PXE-E61: Media test failure, check cable. When I restart, the error doesn’t crop up again and the PC functions normally. Please solve my problem.

Gyanesh Dutt, Chandigarh

A. Probably this error is triggered by an electrical surge or sudden closure of the machine. Now the best solution to resolve this error is to clear all CMOS setting by setting it to default and then shutdown and restart. I have tested exactly the same problem in Windows 2000 and this solution has solved my problem.

Fundet på http://www.tribuneindia.com/2003/20030210/login/drtribune.htm

hvis det var mig ville jeg prøve at finde nogle andre kabler til mit CDROM drev og måske og diskette og Harddisk drev.

faldt over dette


PXE-E61: Media test failure, check cable
>
> Any clue on how to make PXE work as before ?
>
> Cheers,

You probably need a power cycle in between.  You might also need to
disable Wake On LAN or some such.  Clearly the Windows drivers leaves
the card unusable to its own PXE stack.  You should check with DLink if
there are any driver or PXE stack upgrades available, and otherwise
complain.

og her lidt mere hjælp

Hi,

Is the drive recognised in BIOS during the post count

Check the cable is on properly at both ends

Clear NVRAM using the maintenance jumper or in BIOS, different machines / BIOS's do it different ways.

Try the clean1k utility from the resource CD's. I understand this will wipe a drive much the same as the debug script.

One I read of recently was to install a hard disk into a Mac and set it up on that, when you then install it back in a p.c. the BIOS & O/S will consider it to be a blank, unpartitioned & unformated completely blank hard disk straight out of a factory.. Never tried it as I don't have a Mac

Pop the drive into a different computer and partition and format it in that. Personally when doing this I have always taken out, completely & physically the host machines hard disk just to be certain I don't and can't do anything to that hard disk.

I could just disconnect it, but its much more reassuring to be partitioning & formatting hard disks in your computer when the hard disk with all your precious data is sitting on the desk in from of you and nothing Microsoft or you can do could possibly trash the data on it.

hth

Ceri

Jeg har netop oplevet samme problem på et ShuttleX-system jeg er ved at samle. Her hjalp det at loade standard CMOS-instillinger...

Tak for det.


Mvh.
The Unseen