At installere IOS ( Image ) på router 2600

PC & Router skal sidde på samme net i.e. 10.0.0.1/255.0.0.0 10.0.0.2/255.0.0.0
Check at pc kan pinge router
Hvis ikke du har fået startet routeren op uden image ;-)

Alternativt skal du bruge console porten

Dansab >> Du lægger IOS filen i roden at TFTP progremmet.

Log på routeren via console porten og gør følgende (c1710-k9o3sy-mz.122-15.T7) er godt nok til en 1710 men fremgangs måden er det samme.

Router# copy tftp flash
Address or name of remote host []? 10.1.1.1
Source filename []? c1710-k9o3sy-mz.122-15.T7
Destination filename [c1710-k9o3sy-mz.122-15.T7]?
%Warning:There is a file already existing with this name
Do you want to over write? [confirm]
Accessing tftp://10.1.1.1/c1710-k9o3sy-mz.122-15.T7.bin
Erase flash: before copying? [confirm]
Erasing the flash filesystem will remove all files! Continue? [confirm]
Erasing device... eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee
ee ...erased
Erase of flash: complete
Loading c1710-k9o3sy-mz.122-15.T7 from 10.1.1.1 (via Ethernet0):  !!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!
[OK - 3802992/7605248 bytes]

Verifying checksum...  OK (0x1ABC)
3802992 bytes copied in 58.236 secs (65568 bytes/sec)
Router#

Jeg kan ikke starter routeren i rigtig mode Router> eller router#.
Den starter op på Rommon 1> mode hvor jeg ikke kan komme videre.
Mvh
Dansab

dansab ->læs lige reglerne du må ikke åbne flere ens spørgsmål om det samme så tag lige at lukke det andet spørgsmål!!
http://www.eksperten.dk/spm/398974

Kenp:
Jeg beklager meget at jeg ikke har været opmærksom på reglerne.
Mvh
Dansab

dansab ->nu ved du det ;) så husk at ligge et svar i det andet spørgsmål og accepter der selv, du kan læse mere om brugen af eksperten her www.ebruger.dk/faq

Jamen så får du den da også her:

Start men dette også lægger du den nye IOS Image med TFTP som jeg beskrev oppe over.

rommon 2 > confreg

    Configuration Summary
enabled are:
load rom after netboot fails
console baud: 9600
boot: the ROM Monitor

do you wish to change the configuration? y/n  [n]:

rommon 2 > confreg

    Configuration Summary
enabled are:
load rom after netboot fails
console baud: 9600
boot: the ROM Monitor

do you wish to change the configuration? y/n  [n]:  y
enable  "diagnostic mode"? y/n  [n]:
enable  "use net in IP bcast address"? y/n  [n]:
disable "load rom after netboot fails"? y/n  [n]:
enable  "use all zero broadcast"? y/n  [n]:
enable  "break/abort has effect"? y/n  [n]:
enable  "ignore system config info"? y/n  [n]:
change console baud rate? y/n  [n]:
change the boot characteristics? y/n  [n]:  y
enter to boot:
0 = ROM Monitor
1 = the boot helper image
2-15 = boot system
    [0]:  2

    Configuration Summary
enabled are:
load rom after netboot fails
console baud: 9600
boot: image specified by the boot system commands
      or default to: cisco2-C2600

do you wish to change the configuration? y/n  [n]: n

(You must reset or power cycle for new config to take effect)

rommon 3 > reset

System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info


(The router should now reload with a valid Cisco IOS software image.)
rommon 1 > dir flash:
        File size        Checksum  File name 
5358032 bytes (0x51c1d0)  0x7b16    c2600-i-mz.122-10b.bin
rommon 2 >

rommon 2 > boot flash:c2600-i-mz.122-10b.bin
program load complete, entry point: 0x80008000, size: 0x51c0dc
Self decompressing the image : #################################################
##################################
...